新聞中心
Home > News Center > FAQ

What are the methods of using vacuum furnaces?
2024-08-23 17:23:25

The methods of using Vacuum Furnaces involve multiple steps to ensure that the equipment can operate safely and efficiently and meet specific process requirements. The following are the detailed steps of the methods of using Vacuum Furnaces:
1. Preparation
Inspect the equipment:
Before use, carefully check whether the appearance of the vacuum furnace is intact, whether all parts are firmly installed, and whether there is no looseness or damage.
Check whether key components such as vacuum pumps, heating elements, and temperature control systems are in normal condition.
Cleaning the furnace:
Before use, the residues and impurities in the furnace need to be cleaned up to keep the furnace clean and tidy. This helps to reduce thermal resistance during heating and improve heating efficiency.
Prepare samples:
According to process requirements, place the samples to be processed in suitable containers, and ensure that the samples do not come into direct contact with the inner wall of the furnace or the heating elements to prevent contamination or damage.
2. Set process parameters
Set temperature:
According to process requirements, set the required heating temperature in the temperature control system of the vacuum furnace. This is usually done through the numeric keypad or touch screen on the operation interface.
Set vacuum degree:
According to process requirements, set the required vacuum degree. This is usually achieved by adjusting the working state of the vacuum pump during the vacuuming process.
Set other parameters:
Other process parameters such as heating rate, holding time, cooling rate, etc. can also be set as needed. The setting of these parameters should be determined according to the specific process requirements and sample characteristics.
3. Start the equipment
Turn on the vacuum pump:
Press the start button of the vacuum pump to start the vacuuming process. During the vacuuming process, pay close attention to the changes in the vacuum degree and adjust the working state of the vacuum pump as needed.
Heating:
When the vacuum degree reaches the set value, start the heating element for heating. During the heating process, pay close attention to the temperature changes and ensure that the temperature control system works properly.
Monitoring and adjustment:
During the heating and insulation process, the operating status of the equipment and the changes in process parameters should be monitored regularly. If necessary, the parameters such as heating rate, temperature or vacuum degree should be adjusted in time to ensure the stability and consistency of the process.
4. Processing and cooling
Processing:
According to the process requirements, the sample is processed during the heating and insulation process. This may include chemical reactions, sintering, annealing and other processes.
Cooling:
When the processing is completed, the appropriate cooling method should be selected according to the process requirements. Common cooling methods include natural cooling, water cooling and air cooling. During the cooling process, pay close attention to temperature changes and ensure that the cooling rate meets the process requirements.
5. End and cleanup
Shut down the equipment:
When the sample cools to room temperature, turn off the heating element and vacuum pump, and cut off the power supply of the equipment.
Remove the sample:
Open the furnace door or container cover and take out the processed sample. When taking out the sample, be careful to avoid scalding or damaging the sample.
Cleaning and maintenance:
Clean the furnace and the surface of the equipment to remove residues and impurities. Regularly maintain and service the equipment to extend the service life of the equipment and keep it in good working condition.
Precautions
When using Vacuum Furnaces, the safety operating procedures and precautions of the equipment should be strictly followed to ensure the safety of the operator.
When handling flammable, explosive or toxic samples, appropriate safety measures should be taken and the operation should be carried out in a well-ventilated environment.
During use, if you encounter abnormal conditions or failures, you should stop the equipment immediately and seek help and support from professionals.


Site map

Copyright @ 2024 Jiangsu Kingkind Industrial Furnace Co., Ltd. All Rights Reserved

社区国产亚洲欧美另类调教在线观看| 91avfree| 欧美曰韩亚洲二区| 国产欧美视频一区| 久久久精品中国字幕麻豆发布 | 好吊妞干网免费视频| 偷窥导航xxx| 国产日韩国欧在线观看| 日韩色aⅤ| 日日av天天| 国产av电影一区| 日韩免费电影成人| 久久99er6热线精品免费| 依人大香蕉| 少妇国产www| 国产精品一区二区国产馆| 亚洲久久成人电影| 日韩亚洲第9页| 亚洲欧美日韩成人精品| 99九九久久女人| 欧美人妻 一区二区| 大陆日B视频播放免费| 国内激情精品| 色就是色欧美用力| 丁香五月婷婷一区二区| 国产精品成人vP一区二区| 国产乱老熟视频乱老熟女51| www色欧美一区| 伊人久亚州| 亚洲精品国产污污在线观看| 夜久久波多| 日本女优精品久久久| www.日本久久久久久.com. | 久久久久久久久久午夜视频| 欧美双插性视频| 日韩 一区二区 亚洲| 欧美精品3P| 大香蕉尹老师| 日韩欧美中文字幕七区| 午夜欧美毛片| 国产区一区二区三久久|